Hydro flame fan removal

RV and bus conversion info since 1996.

Share Your Feedback

PRINT PAGE

RV Classifieds

		2002 Volkswagen Eurovan Winnebago Camper - $9,200
		2007 Bounder 38V - $149,900
		2000 Safari Trek 2430 - $32,995
		1995 Kountry Star M-32RKSA - $22,900
		1997 Eagle American Coach - $56,000
		VIEW ALL
		Search RV Classifieds
		Classifieds Policies
		Benefits for Dealers
		Sell Your RV
		Dealer Signup

Useful Links

RV Community

		Discussion Groups
		RV Articles
		RV FAQs
		RV Classified Ads
		Virtual RV Park
		Shop at our Store
		RV Lifestyle Books
		Rate Your RV
		AllThingsRV.com
		MyRVGuide.com
		RVMechanic.com
		Advertise With Us

BECOME A MEMBER

RV Resources

		e RV Loans
		Sculptures for your RV
		Visit Rio Rancho, NM for Winter
		RV Dealers
		RV Manufacturers
		RV Rentals
		RV Glossary
		RV Types
		RV Ratings

Hydro flame fan removal

Home > Discussion Forum > Mechanic's Corner (general)

email Walt

reply to message

post new message

search forums

hidden layer

ATTENTION: All Postings that advertise items for sale will be deleted from the Discussion Forum. You may post sale items for free in the Classifieds section. Sign up now.

All Messages in Thread	Author	Date
Hydro flame fan removal	Walt	1-31-08
Repair manual for Excalibur-II model 8935. I'm trying to remove fan motor from furnace without removing furnace. I would appreciate any help.
Re: hydro flame fan removal	David	5-1-08
Keith, I have an Atwood Hydro Flame Model 8535-IV. Could not locate your ref. procedure dated 2-10-08. Would your procedure dated 3-30-08 apply? Thanks David
Re: hydro flame fan removal	Keith	1-31-08
Hi Walt, I emailed you the procedure. Hope it helps! Keith
Re: hydro flame fan/motor removal	Earl Acklin	2-12-08
I have a Hydro Flame 8500 III, 8900 II I've taken out every screw and still it wont come out. I have removed any on the backside. It it spot welded in or something? Earl
Re: hydro flame fan/motor removal	Earl Acklin	2-12-08
I have all the screws removed and still I cant get the fan/motor removed. Is it spot welded in? What do I do next?
Re: hydro flame fan removal	Keith	3-30-08
Turn off propane, remove one screw from the timer relay (has 4 wires going to it on left front cover) loosen the other and pull it loose. Remove 4 screws from the plastic cover it is on and remove the cover, remove the PC board, remove the exhaust tube, take the propane line loose, take the igniter wire(red)loose and one quick disconnect wire (both on propane line side), remove 3 - 4 screws from rear that hold the burner in and one on the round edge, pull out the burner, loosen set screw on the small fan, hold the large fan and rock the small one while pulling to remove it. There are 3 hex screws behind the small fan remove them and you should be able to pull the motor and blower fan out as one assembly. Remove and install fan on new motor, reverse all this to install. You may have to change one wire connector on the new motor to hook it up. Pay attention to where the motor wires were connected as the motor will run backwards if you reverse them. Hope this helps, good luck! Keith Note: this is for II & III series. IV is similar, but the motor is held in with a hose clamp, it isn’t hard to figure out the difference‘s.
Re: hydro flame fan removal	Keith	2-18-08
Please see Hydro Flame fan noise dated 02-10-08 for procedure. Keith
Re: hydro flame fan removal	Mack Yarbrough	3-23-08
I have the Hydro Flame Excalibur 8535-II model and it makes a lot of noise from the fan area. Is there a method to remove and test? If so could some one send me the disassembly procedure? Thanks Mack
Re: hydro flame fan removal	Otto Winkelmann	2-26-08
I need the same removal information. I have an Atwood Hydro Flame 8531-III furnace and the fan motor needs lubrication or replacement. Would you please e-mail me the removal/replacement information also? Thanks very much
Re: hydro flame fan removal	Sal	2-5-08
I have the same problem Keith, Could you give me some advice ob how to. Thanks
Re: hydro flame fan removal	Charles	2-18-08
Can someone send me the instructions on the fan removal also. PLEASE
Re: hydro flame fan removal	Dave	2-11-08
Hello Kieth Same problem with a 8535 II. Can you e-mail me the procedure too? Thanks Dave
Re: hydro flame fan removal	John	3-30-08
Need to replace fan motor in 8535 hydroflame.Also having problem with 13500 A/C unit that kicks breaker sometimes on 30 amp a/c outlet. 4000 watt generator will not run a/c. Thanks